Ultra Silk PLA Filament, Silky Glossy Finish Filament, 1.75mm,+/-0.03mm, 1kg(2.2LBS)/Spool, Ultra Silk Black

Love this filament and fits on my Bambu A1 ams which is a bonus, beautiful colours and no problems with lots of prints

I use this brand of PLA almost exclusively. Amazing quality, never any issue and plenty of colours / effects to choose from.Highly recommend!

I bought this for my husband and he is absolutely thrilled with it. Looks great when printed. Came well packaged and arrived quickly. Very good value for money.

I was looking for a gold filament for a project so ordered this. The filament arrived seal packed with a small pouch of silica to avoid moister contamination, and seemed well packed and protected.I had no issues using the filament, and it ran through perfectly with no tangles or snags. The filament is in my opinion very brittle so you may well have issues with anything using a lot of high or thin support areas.The finish of the filament is very clean and I managed to get some really smooth prints from it. The colour shown is a very good match for the finished print. It didn’t quite match the gold colour I was after for my project but that was my fault in colour choice, not the filament which is more on the lighter yellow gold side, and as I say the pictures are a good match for the colour.Overall a good smooth filament that produced some nice clean prints, it is quite brittle so in my opinion not suitable for projects with a lot of support.

I saw this filament and thought to myself I need to try it! The gradient change is quick! So quick in fact that I think it only really works on the flat parts of prints, tops and bottoms. I found that the change in colour on the walls was too quick for larger/longer prints. It was a super easy filament to use and as always the quality speaks for itself as well as amazing value for money!

Failed and clogged one of my Bambu, changed nozzle, happened again, stuck it on a different Bambu and happened again, took it off to return and thought I would give it a quick measure. Noticed for starters it says it has a variable of 0.03mm not 0.02 as listed BUT this wasn't the issue, as per my photo the filaments diameter is less than 1.6mm diameter so just slips in extruder!!!!

I have used Eryone a few times before and it has always given me a good reliable standard of print and I think there silk rainbow filament is no different.I printed this filament at 195 degrees without any issues. If there are any issues with the prints its normally my user error which can be removed with a little fine tuning of retraction etc which is normal when you change filaments as they use different additives.The things I look for in good filament when I get it is a consistency of the thickness of the filament which in this case should be 1.75mm. You can see this filament is within the tolerances they claim and I measured multiple places along the filament and it remained pretty consistent. (I have added a picture to support that)The 2nd thing I look for is how the filament lays down on that critical first layer. The rainbow filament is beautiful when it lays down on the bed (I printed at a bed temp of 50 degrees) but don't take my word for it check out the added picture.In general you can see from the images the smooth shiny surface you would expect from a silk filament and I have added some pictures so you can see the colour change and what you can expect when you print this filament.If I had any negatives it would be that I felt I was missing the blues from the picture showed however this is a very minor issue and may have been just my one roll.One further thing I would mention with Eryone is there great customer service. I have had a bad roll from so many companies usually due to moisture and it can happen to any company you buy from. What I would expect from a good filament company is that the company replaces that roll if its very bad without fuss (although I will normally try a dryer first) Eryone have always had for me one of the best responsive and easiest customer service to deal with.This is an easy choice to buy this filament and if its on one of there deals snap it up and have fun printing it.

Only tried this on a Weedoo Tina 2 so far and its good. No clogging, great print. Could do with a smaller spool - 250 or 500 but I printed a flex dragon with this and it was excellent.